New Install: Pacific Alderlea T6 or Jotul F55

[begreen]

I always thought that there was some cross-polination between Enviro and PE or an engineer switched. The two factories are quite close to each other. The Kodiak had the linked secondary air control, just like the PE Super.

 

[Kodiak]

Ok, so im getting ready to mortar my tilesfor my hearth pad...but I am installiong an OAK. The manual shows both the down and out way and the horizontal way. Is cutting a hole in hearth pad ok? I thought the hearth pad would need to be continuous? Is there a chance that embers could go down into my OAK opening? Should i just keep hearth pad solid ( not drill or cut a hole in it) and just run the OAK out the back wall horizontizally and then outside?

I guess the short version of what im asking is...Is it safeto have a hole in the middle of my hearth pad for my OAK?

 

[stoveliker]

Interesting thought!
I'd say that in principle if the OAK pipe is metal, there's no issue as the ember protection will be continuous.

 

[begreen]

Agreed. Connected with rigid or flexible metal ducting, it's a non-issue.

 

[Kodiak]

Ok. Right on. Good feedback. I guess I’m over thinking it. I guess I had visions of a random small ember getting out the front of the stove when the door is open, going under the stove , and then nestling itself between the opening and the oak pipe where there could be a small chance of it igniting….i mean theoretically maybe?

I just recall someone years ago saying,…“think carefully before you invite fire into your home. “

 

[Kodiak]

Getting ready to install. We will need to use an elbow indoors to align the outdoor pipe further away from a higher adjacent roof to keep it 10ft away. If we do the straight shot we’d have to add approx 6-8ft more pipe. I’d prefer the straight shot for cleaning ease but it would be way to high to get at. Is the elbow really an issue when it comes draft? The elbow will be indoors and approx 10 feet above the stove. Indoor ceiling height is 12 feet. Overall chimney height is 18-20 feet. Seems like that’s plenty of length for draft to overcome the one elbow.

Cleaning will be trickier with the elbow. Guess a top down from exterior to elbow and then a bottom up to elbow from inside with flexible brush. How do I clean out the elbow without removing it? Or is a 45 steep enough to let the debris and ash fall down enough? I do t want creosote or anything accumulating in the elbow after cleaning.

Again , I’m probably over thinking it but let me know what comments you guys have on any of that. Thanks.

 

[begreen]

It would be easier to visualize with a drawing and maybe a site picture.

 

[EbS-P]

Getting ready to install. We will need to use an elbow indoors to align the outdoor pipe further away from a higher adjacent roof to keep it 10ft away. If we do the straight shot we’d have to add approx 6-8ft more pipe. I’d prefer the straight shot for cleaning ease but it would be way to high to get at. Is the elbow really an issue when it comes draft? The elbow will be indoors and approx 10 feet above the stove. Indoor ceiling height is 12 feet. Overall chimney height is 18-20 feet. Seems like that’s plenty of length for draft to overcome the one elbow.

Cleaning will be trickier with the elbow. Guess a top down from exterior to elbow and then a bottom up to elbow from inside with flexible brush. How do I clean out the elbow without removing it? Or is a 45 steep enough to let the debris and ash fall down enough? I do t want creosote or anything accumulating in the elbow after cleaning.

Again , I’m probably over thinking it but let me know what comments you guys have on any of that. Thanks.

Use 45s or 30s if you can.

 

[kborndale]

A sooteater will go thru a 45.

 

[Kodiak]

I’m about to commit to my hearth pad depth. I’m not including the ash lip in my required 18” ( Canada ) from stove opening to edge of hearth pad. Can someone please tell me the actual ash lip depth for the t6. Thankyou.

PS. We are also going for a straight shot from chimney stove collar all the way to roof deck (14 ft) then the elbow ideally a 45, and another 6-8 ft to get above the nearest roof line. The elbow moves the alignment away from an adjacent higher roof as well to meet the minimum 10 ft away. I’ll post some pics later so it’ll make sense for those interested.

 

[Kodiak]

Oh yeah, the nice thing is that we wont have any elbow indoors which imo is more pleasing. And if needed leaves the elbow cleaning outdoors and the mess out there if ever needed to remove it for some reason.

 

[Kodiak]

Stove arrived today. Installing tomorrow. Pretty excited. I’m darn impressed with how great this stove looks, it’s really aesthetically pleasing. It looks good in the photos but it’s real nice in person.

Ill look for articles on how to do the first few burns properly this weekend.

Cheers yall.