The Chimney Sweep Online Fireplace, Woodstove, Gas Stove and Barbecue Shop
STOVE DIMENSIONS (PEDESTAL): 24" WIDE X 25" DEEP X 29 1/8" TALL STOVE DIMENSIONS (CAST LEGS): 24" WIDE X 25" DEEP X 28" TALL CONNECTOR PIPE USED: 6" SINGLE-WALL OR DOUBLE-WALL STOVEPIPE
HEARTH (FLOOR PROTECTION) REQUIREMENT: ANY 1/4" NON-COMBUSTIBLE MATERIAL MINIMUM HEARTH EXTENSION BEYOND SIDES OF STOVE... 5" MINIMUM HEARTH EXTENSION BEYOND DOOR OF STOVE... 16" MINIMUM HEARTH EXTENSION BEYOND REAR OF STOVE.... 0"
FLAT WALL INSTALLATIONS:
| CORNER INSTALLATIONS:
|
A: STOVE TO BACKWALL: SINGLE-WALL STOVEPIPE.... 12" DOUBLE-WALL STOVEPIPE..... 5" MOBILE HOME*.............. 8" ALCOVE*.................. 10" | G: STOVE TO CORNER WALLS: SINGLE-WALL STOVEPIPE... 11" DOUBLE-WALL STOVEPIPE.... 4" MOBILE HOME*............. 8" |
B: STOVE TO SIDEWALL: SINGLE-WALL STOVEPIPE.... 18" DOUBLE-WALL STOVEPIPE.... 14" MOBILE HOME*............. 16" ALCOVE*.................. 16" | H: CENTERLINE PIPE TO CORNER WALLS: SINGLE-WALL STOVEPIPE... 25" DOUBLE-WALL STOVEPIPE... 18" MOBILE HOME*............ 22" |
C: CENTERLINE PIPE TO BACKWALL: SINGLE-WALL STOVEPIPE.... 22" DOUBLE-WALL STOVEPIPE.... 15" MOBILE HOME*............. 18" ALCOVE*.................. 20" | I: DIAGONAL CORNER TO FRONT OF HEARTH: SINGLE-WALL STOVEPIPE... 67" DOUBLE-WALL STOVEPIPE... 57" MOBILE HOME*............ 63" |
D: CENTERLINE PIPE TO SIDEWALL: SINGLE-WALL STOVEPIPE.... 30" DOUBLE-WALL STOVEPIPE.... 26" MOBILE HOME*............. 28" ALCOVE*.................. 28" | J: CORNER TO EDGE OF HEARTH: SINGLE-WALL STOVEPIPE... 60" DOUBLE-WALL STOVEPIPE... 53" MOBILE HOME*............ 57" |
E: MINIMUM HEARTH WIDTH..... 34" | L: WIDTH OF HEARTH FRONT... 34" |
F: BACKWALL TO FRONT OF HEARTH: SINGLE-WALL STOVEPIPE... 53" DOUBLE-WALL STOVEPIPE... 46" MOBILE HOME*............ 49" ALCOVE*................. 51" |
COMBUSTIBLE ALCOVE DIMENSIONS:
MINIMUM 56" Wide MINIMUM 90" Tall MAXIMUM 48" Deep |
OUTSIDE AIR SUPPLIED FROM CRAWLSPACEInstall a length of 4" rigid or flexible aluminum intake pipe down through a 4-1/8" hole in the floor anywhere under the pedestal, extending below the floor joists and insulation. The intake pipe doesn't attach directly to the stove: snip and flare the pipe at the top to hold it in place. Use silicone cement to glue a piece of 1/4" wire rodent mesh at the bottom. | OUTSIDE AIR SUPPLIED THROUGH BACKWALLRemove the air intake cover from the back of the pedestal and insert a length of 4" rigid or flexible aluminum intake pipe extending through 4-1/8" hole in outside wall behind the stove. Attach a standard 4" dryer vent termination on the outside of the wall, removing the flapper plate and substituting a piece of 1/4" rodent mesh silicone-cemented in place. |
OUTSIDE AIR SUPPLIED FROM CRAWLSPACEInsert a length of 4" rigid or flexible aluminum intake pipe into the knockout hole in the bottom of the air plenum and extend it down through a 4-1/8" hole in the floor, terminating below the floor joists and insulation. Caulk around the intake pipe where it penetrates the floor and use silicone cement to glue a piece of 1/4" wire rodent mesh to the bottom. | OUTSIDE AIR SUPPLIED THROUGH BACKWALLInsert a length of 4" rigid or flexible aluminum into the knockout hole in the rear of the air plenum and run back through a 4-1/8" hole in the outside wall behind the stove. Attach a standard 4" dryer vent termination on the outside of the wall, removing the flapper plate and substituting a piece of 1/4" rodent mesh silicone-cemented in place. |