The Chimney Sweep Online Fireplace, Woodstove, Gas Stove and Barbecue Shop
STOVE DIMENSIONS: 27-1/2" WIDE X 19" DEEP (TOP), 21.5" DEEP (LEGS) X 30-1/4" TALL CONNECTOR PIPE USED: 6" SINGLE-WALL OR DOUBLE-WALL STOVEPIPE
MINIMUM HEARTH (FLOOR PROTECTION) REQUIREMENTS: ANY SOLID, NON-COMBUSTIBLE MATERIAL AT LEAST 1/4" THICK MINIMUM HEARTH EXTENSION FROM BACK PLATE OF STOVE....... 5-1/2" MINIMUM HEARTH EXTENSION FROM LOADING DOOR SIDE OF STOVE... 16" MINIMUM HEARTH EXTENSION FROM SOLID SIDE OF STOVE....... 4-1/2" MINIMUM HEARTH EXTENSION FROM FRONT DOOR OF STOVE.......... 16"
FLAT WALL INSTALLATIONS: | CORNER INSTALLATIONS SIDE DOOR DISABLED: | FIREPLACE INSTALLATIONS: |
A: STOVE TO BACKWALL:
SINGLE-WALL STOVEPIPE.. 16"
DOUBLE-WALL STOVEPIPE
AND REAR HEAT SHIELD.... 6"
| G: STOVE TO CORNER WALLS:
SINGLE-WALL STOVEPIPE...... 8"
DOUBLE-WALL STOVEPIPE
AND REAR HEAT SHIELD....... 8"
| M: HEARTH TO OVERHEAD COMBUSTIBLES: TRIM (1-1/2" DEEP)....... 48" MANTEL (12" DEEP)........ 48" |
B: SOLID SIDE OF STOVE TO WALL:
SINGLE-WALL STOVEPIPE.. 16"
DOUBLE-WALL STOVEPIPE
AND REAR SHIELD.........16"
|
H: CENTERLINE PIPE TO WALLS:
SINGLE-WALL STOVEPIPE: 21-1/4"
DOUBLE-WALL STOVEPIPE
AND REAR HEAT SHIELD.. 21-1/4"
| N: MINIMUM HEARTH DEPTH IN FRONT OF FIREPLACE OPENING, INCLUDING EXTENSION IF NEEDED...... 38" |
C: CENTER OF PIPE TO BACKWALL:
SINGLE-WALL STOVEPIPE.. 21"
DOUBLE-WALL STOVEPIPE
AND REAR HEAT SHIELD... 11"
|
I: DIAGONAL FROM CORNER TO LOP:
SINGLE-WALL STOVEPIPE..... 65"
DOUBLE-WALL STOVEPIPE
AND REAR HEAT SHIELD.. 63-1/2"
| O: LINER SIZE REQUIRED....... 6" P: MINIMUM OPENING HEIGHT FOR REAR VENT PIPE... 26-3/4" |
D: CENTER OF PIPE TO SIDEWALL,
SOLID (NON-DOOR) SIDE:
SINGLE-WALL PIPE... 29-3/4"
DOUBLE-WALL STOVEPIPE
AND REAR SHIELD.... 29-3/4"
|
J: WALLS TO EDGE OF HEARTH:
SINGLE-WALL STOVEPIPE..... 59"
DOUBLE-WALL STOVEPIPE
AND REAR HEAT SHIELD...... 58"
| |
E: MINIMUM HEARTH WIDTH: W/16" DOOR SIDE ONLY... 48" W/16" BOTH SIDES....... 60" | ||
F: BACKWALL TO FRONT OF HEARTH:
SINGLE-WALL STOVEPIPE.. 51"
DOUBLE-WALL STOVEPIPE
AND REAR HEAT SHIELD... 41"
| COMBUSTIBLE ALCOVE DIMENSIONS (SIDE DOOR DISABLED) MINIMUM 61" WIDE X 64" TALL MINIMUM 20" REAR CLEARANCE |
OUTSIDE AIR SUPPLIED FROM VENTILATED CRAWLSPACEBolt optional outside air adapter to Heritage at bottom rear. Attach a length of 3" rigid or flexible aluminum pipe to the intake collar with a 3" pipe clamp, then elbow down through a 4-1/8" hole in the floor behind the stove, extending the pipe below the floor joists and insulation. Caulk around the pipe where it penetrates the floor and use silicone cement to glue on a piece of 1/4" wire rodent mesh at the bottom. | OUTSIDE AIR SUPPLIED THROUGH BACKWALLBolt optional outside air adapter to Heritage at bottom rear. Attach a length of 3" rigid or flexible aluminum intake pipe to the intake collar with a 3" pipe clamp, extend through a 4-1/8" hole in the outside wall behind the stove. Attach a standard 4" dryer vent termination on the outside of the wall, removing the flapper plate and substituting a piece of 1/4" rodent mesh silicone-cemented in place. |
Fireplace Hearth Installations:Use a short length of 6" stainless liner pipe to connect the stove to a stainless tee with a cap on the bottom. On the roof, attach a rigid - flex connector to the bottom of a length of flexible stainless and snake it down through the damper, plugging it into the tee at the bottom (cut out the damper assembly to make room if necessary). Use high-temp silicone sealant to attach a stainless sealer plate to the top of the chimney, and complete the installation with a storm collar and rain cap at the top. |